Tools Needed:- Measuring cup (4-8 fl. oz.)- Pitcher (at least 32 fl. oz.)- Towel(s)*NOTE: If your machine fails to power on or fails to heat, skip to the end of this article.1. Start by powering the machine on and allowing it come to full...
Tools Needed:- 2.5mm Allen wrench or hex driverNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the drip tray, cup tray and reservoir.2. Remove the six Allen head screws from the top panel as...
Tools Needed:- Small flat bladed screwdriverNOTE: It's best to unplug the machine and allow it to fully cool before re-setting these switches.1. Start by removing the top panel from the machine.2. Identify the two safety switches screwed into the...
Tools Required:- 2.5mm Allen wrench or hex driver- 17mm wrench or adjustable wrench- Recommended: 17mm deep socket and socket wrench with extension- Vacuum Breaker Rebuild KitNOTE: The machine should be unplugged and cool to the touch before you...
Tools Needed:- 13mm crescent wrench- Scouring pad or steel wool or wire bristle brushNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the panels from the machine.2. Create room to work by removing...
Tools Needed:- 14mm crescent wrench- Scouring pad or steel wool or wire bristle brushNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the panels from the machine.2. Create room to work by removing...
Tools Needed:- 3mm Allen wrench or hex driver- Towel1. Start by draining the machine's boiler.2. Next, remove the panels from the machine.3. Tilt the machine onto its front, so that it rests on the lower part of the frame and the E61 group head....
Tools Needed:- Adjustable wrenches (x2)- Pick or other similar implement- Towel- Molykote food safe lubricant- Replacement spindle seat valve gasket- Channel-lock pliers or locking pliers1. Start by opening the valve all the way by turning the...
Tools Needed:- 3mm Allen wrench or hex driver.- Multimeter- Towel 1. Start by draining the machine. Then unplug the machine and allow it to cool.2. Tilt the machine up onto its front, carefully resting it on the group head. You may want to place a...
Tools Needed:- 3mm Allen wrench or hex driver- 13mm deep socket and socket wrench- Flat bladed screwdriver1. Start by draining the machine. Then unplug the machine and allow it to cool.2. Tilt the machine up onto its front, carefully resting it on...
Tools Needed:- 2.5mm Allen wrench or hex driver- Flat bladed screwdriver- Dental pick or similar implement- Replacement expansion valve seatNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the top...
Tools Needed:- 20mm crescent wrenchOR- 20mm deep socket and socket wrench- PTFE tape (aka Teflon tape aka plumber's tape)- Replacement safety valveNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing...
Tools Needed:- 3mm Allen wrench or hex driver- Replacement bulb filter- Towel1. Start by draining the machine. Then unplug the machine and allow it to cool.2. Tilt the machine up onto its front, carefully resting it on the group head. You may want...
Tools Needed:- 14mm crescent wrench- Adjustable wrench- #2 Philips screw driver- Wire brush or scouring pad1. Start by draining the boiler, then unplug the machine and allow it to cool.2. Remove the panels from the machine.3. Create room to work...
Tools Needed:- Small adjustable wrench- Towel1. Make sure the knob is fully closed.2. Use the small adjustable wrench to loosen and remove the retaining nut in the center of the knob. You may want to drape a small towel over the knob, to avoid...
Tools Needed:- 3mm Allen wrench or hex driver- 2.5mm Allen wrench or hex driver- Small adjustable wrenchNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the panels from the machine.2. Identify the...