Tools Needed:- #2 Philips screwdriverNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the drip tray, cup tray and reservoir.2. Remove the eight Philips head screws from the top panel shown here....
Tools Needed:- Measuring cup (4-8 fl. oz.)- Pitcher (at least 32 fl. oz.)- Towel(s)*NOTE: If your machine fails to power on or fails to heat, skip to the end of this article.1. Start by powering the machine on and allowing it come to full...
Tools Needed:- #2 Philips screwdriver.- Multimeter- Towels1. Start by draining the machine. Then unplug the machine and allow it to cool.2. Tilt the machine up onto its front, carefully resting it on the group head. You may want to place a towel...
Tools Needed:- #2 Philips head screwdriver- 38mm deep impact socket- Impact driver- Replacement heating element- Replacement heating element gasket1. Start by draining the machine. Then unplug the machine and allow it to cool.2. Tilt the machine...
Tools Required:- 2.5mm Allen wrench or hex driver- 17mm wrench or adjustable wrench- Recommended: 17mm deep socket and socket wrench with extension- Vacuum Breaker Rebuild KitNOTE: The machine should be unplugged and cool to the touch before you...
Tools Needed:- Small flat bladed screwdriverNOTE: It's best to unplug the machine and allow it to fully cool before re-setting these switches.1. Start by removing the top panel from the machine.2. Identify the two safety switches screwed into the...
Tools Needed:- 20mm crescent wrenchOR- 20mm deep socket and socket wrench- PTFE tape (aka Teflon tape aka plumber's tape)- Replacement safety valveNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing...
Tools Needed:- - Adjustable wrench- Pick or other similar implement- Towel- PTFE tape aka Teflon plumber's tape- Replacement spindle seat valve gasket1. Start by opening the valve all the way by turning the knob counter-clockwise.2. Identify the...
Tools Needed:- #2Philips screwdriver- 7mm socket or hex nut driver- Small adjustable wrenchNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the panels from the machine.2. Identify the SSR bracket...
Tools Needed:- 19mm deep socket and ratcheting wrench- 14mm deep socket- 17mm open-ended wrench- PTFE tape aka Teflon plumber's tape- Scouring pad or steel wool or wire bristle brush1. NOTE: The machine should be unplugged and cool to the touch...
Tools Needed:- 7mm wrench or deep socket1. Start by removing the panels from the machine.2. Use the 7mm wrench or a 7mm deep socket and ratchet to remove the retaining nuts on the reservoir mounting studs as shown. 2. You can now lift up the...
Tools Needed:- 17mm crescent wrench- Scouring pad or steel wool or wire bristle brushNOTE: The machine should be unplugged and cool to the touch before you begin.1. Start by removing the panels from the machine.2. If necessary, create room to work...
- #2 Philips screwdriver- Towels1. Start by fully draining the machine:Lelit Mara X: Draining the Machine2. Tilt the machine forward and rest it on its front, placing a towel underneath the group head and frame to protect the machine and your work...
Tools Needed: Phillips head screw driver 7mm wrench or deep socket 12mm Crescent Wrench 13mm Crescent Wrench Flathead screw driver (optional) PTFE tape Replacement pump 1. First, you will need to remove the panels of your machine, you can follow...
Tools Needed: 21mm crescent wrench or adjustable wrench Second adjustable wrench Pick or small prying implement PTFE tape OR food safe thread sealant Food grade lubricant New plumbing seat (if needed)- Note: The machine should be unplugged and...
Tools Needed: Philips head screwdriver 17mm crescent wrench 14mm crescent wrench PTFE tape OR food safe thread sealant Replacement steam delivery tube (reach out to our Tech Department to order) 1. Remove the top panel to gain access to this...
Tools Needed: Philips head screwdriver Small flat head (optional) New CPU if necessary (Please see Tech Department to secure replacement parts)1. First, unplug your machine, and then remove the panels.2. Locate the CPU on the left side of the...
Tools Needed:Portafilter with back flush disc installedPhillips head screwdriver12mm crescent wrenchPliers/tweezers (if removing the gasket seat for service)1. Remove the top panel from your machine and locate the expansion valve.2. Lock your...